PKTC-DECT-MIB DEFINITIONS ::= BEGIN
IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    Unsigned32,
    Counter32
                       FROM SNMPv2-SMI
    OBJECT-GROUP,
    MODULE-COMPLIANCE
                       FROM SNMPv2-CONF
    SnmpAdminString
                       FROM SNMP-FRAMEWORK-MIB
    TEXTUAL-CONVENTION,
    TruthValue,
    DateAndTime
                       FROM SNMPv2-TC
    ifIndex            FROM IF-MIB
    pktcApplicationMibs
                       FROM CLAB-DEF-MIB;

pktcDectMib MODULE-IDENTITY
LAST-UPDATED "200909170000Z" -- September 17, 2009
    ORGANIZATION "Cable Television Laboratories, Inc."
    CONTACT-INFO
            "Broadband Network Services
             Cable Television Laboratories, Inc.
             858 Coal Creek Circle,
             Louisville, CO 80027, USA
             Phone: +1 303-661-9100
             Email: mibs@cablelabs.com

             Acknowledgements:
             Thomas Clack, Broadcom
             Eugene Nechamkin, Broadcom
             Josh Littlefield, Cisco
             Jerry Mahler,  Motorola
             Eduardo Cardona, CableLabs"
    DESCRIPTION
            "This MIB module contains the PacketCable client
            HD Voice management requirements."
    REVISION "200909170000Z" -- September 17, 2009
    DESCRIPTION
            "Revised version includes ECN
            DECT-PROV-N-09.0576-7
            and published as part of PKT-SP-DECT-PROV-I02"
    REVISION "200902260000Z" -- February 26, 2009
    DESCRIPTION
            "Initial version, published as part of the CableLabs
            DECT Provisioning Specification PKT-SP-DECT-PROV-I01-090226
            Copyright(c) 2009 Cable Television Laboratories, Inc.
            All rights reserved."
    ::= { pktcApplicationMibs 4 }

-- Textual Conventions

PktcSpecVersion ::= TEXTUAL-CONVENTION
    STATUS      current
    DESCRIPTION
            "This data type represents the publication spec number of
            the corresponding requirement being referenced.
            PacketCable specifications have the notation
            PKT-SP-<SPECNAME>I<##>-YYMMDD.
            This value corresponds to the integer representation
            of <##>."
    REFERENCE
            "PacketCable DECT-HDV Specification."
    SYNTAX      Unsigned32

PktcDectPPState ::= TEXTUAL-CONVENTION
    STATUS      current
    DESCRIPTION
            "This data type describes the DECT PP MAC later state
            or status indication.
            The combination of states and status provide remote
            debugging capabilities by knowing the actions that
            determines e.g., the fallback to a specific state.
            Some values may have a temporary duration and not
            observable due their transient nature. Event logging
            might be defined for such cases.

            Below are the states definitions as defined by the DECT
            standard
            'activeLocked'
            where the PP is synchronized to at least one RFP
            transmission and has one or more connections in progress.
            'idleLocked'
            where the PP is synchronized to at least one RFP transmission.
            It is able to make or receive connections, but has no
            connections in progress.
            'activeUnlocked'
            where the PP is not synchronized to any RFP transmissions,
            and is unable to make or receive connections.
            The PP makes occasional attempts to detect a suitable RFP
            and enter the 'IdleLocked' state.
            'idleUnlocked'
            The PP is not synchronized to any RFP and does not attempt
            to detect RFPs.

            Other values.
            The state  'activeUnlocked' does not define any possible
            reason why the PP has not progressed into a locked state.
            Below are possible values to report:
            'noFPInRange'
            The PP could not find any FP in range.
            'waitingEasyPairing'
            The PP is waiting for easy pairing to be activated by the FP.
            'easyPairingFailed'
            The FP rejects the easyPairing access rights request.
            'easyPINFailed'
            The FP rejects the easyPIN access rights."
    REFERENCE
            "PacketCable DECT-HDV Specification."
    SYNTAX  INTEGER {
                     unknown(1),
                     idleUnlocked(2),
                     activeUnlocked(3),
                     idleLocked(4),
                     activeLocked(5),
                     noFPInRange(6),
                     waitingEasyPairing(7),
                     easyPairingFailed(8),
                     easyPINFailed(9)
                    }

-- Object Definitions
pktcDectNotifications OBJECT IDENTIFIER ::= { pktcDectMib 0 }
pktcDectObjects       OBJECT IDENTIFIER ::= { pktcDectMib 1 }
pktcDectFP            OBJECT IDENTIFIER ::= { pktcDectObjects 1 }

pktcDectFPMaxNumPP OBJECT-TYPE
    SYNTAX      Unsigned32
    UNITS       "PPs"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the maximum number of PPs
            supported by the FP."
    REFERENCE
            "PacketCable DECT-HDV Specification."
    ::= { pktcDectFP 1 }

pktcDectFPMaxActivePP OBJECT-TYPE
    SYNTAX      Unsigned32
    UNITS       "PPs"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "This attribute represents the maximum number of PPs that
            can reach the state Idle_Unlocked simultaneously. The FP
            ages out PPs as soon as the PP leaves the Idle_Unlocked
            state to either Active_unlocked or unknown, allowing
            another PP to attempt synchronization with the FP.
            By Default this attribute reports the MaxNumPP
            attribute value."
    REFERENCE
            "ETSI EN 300 175-3, Digital Enhanced Cordless
            Telecommunications (DECT);Common Interface (CI); Part 3:
            Medium Access Control (MAC) layer"
    ::= { pktcDectFP 2 }

pktcDectFPLockListCfg    OBJECT-TYPE
    SYNTAX      BITS {
                       listOfSupportedLists(0),
                       missedCallsList(1),
                       outgoingCallsLlist(2),
                       incomingAcceptedCallsList(3),
                       allCallsList(4),
                       contactList(5),
                       internalNamesList(6),
                       dectSsystemSettingsList(7),
                       lineSettingsList(8),
                       unused9(9),
                       unused10(10),
                       unused11(11),
                       unused12(12),
                       unused13(13),
                       unused14(14),
                       unused15(15),
                       unused16(16),
                       unused17(17),
                       unused18(18),
                       unused19(19),
                       unused20(20),
                       unused21(21),
                       unused22(22),
                       unused23(23),
                       unused24(24),
                       unused25(25),
                       unused26(26),
                       unused27(27),
                       unused28(28),
                       unused29(29),
                       unused30(30),
                       unused31(31)
                }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute indicates the lock state of user
            invocation of access list 'Edit entry', 'Save entry',
            'Delete entry and 'Delete list' commands.

            If a bit it set to '1' it indicates the corresponding
            list is locked for the commands listed above.

            If a bit is set to '0' the bit associated list is not
            locked for the modification commands listed above.

            A bit set to a non supported list is ignored and returned
            as '0' on a subsequent read operation of this attribute.

            Other list commands are always allowed.
            The default value is the bit set to '1' for all lists that
            the device supports as editable lists."

    ::= { pktcDectFP 3 }

pktcDectFPZeroEmissionEnabled    OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute indicates the status of the Zero Emission
            mode.
            the value 'true' indicates Zero Emission is enabled and the
            FP will invoke the initiation of the no-emission mode if all
            registered PPs are no-emission capable."
    DEFVAL      { true }
    ::= { pktcDectFP 4 }

pktcDectFPPairingType    OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the control of the PP
            registration using PIN or easy registration procedures.
            Setting this attribute to values containing ascii octets
            not in the range [0-9] returns an error.
            The value '0000' indicates the easy paring procedure is
            used for registering new PPs. Otherwise, the PIN procedure
            is used."
    DEFVAL      { "0000" }
    ::= {pktcDectFP 5 }

pktcDectFPEasyPairingActivate    OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the control of easy pairing
            invocation by the FP.

            The value 'false' indicates easy pairing is not active.
            The value 'true' indicates the FP initiates the easy pairing
            process.
            After the first PP attempts pairing or a timer expires,
            which ever occurs first, the easy pairing is disabled and
            this attribute falls back to 'false'."
    DEFVAL      { true }
    ::= {pktcDectFP 6 }

pktcDectFPName    OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute corresponds to the FP name."
    ::= {pktcDectFP 7 }

pktcDectFPGeneralCapabilities    OBJECT-TYPE
    SYNTAX      BITS { none(0)
                }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the General FP capabilities.
            A bit set to '1' indicates support of the specific
            profile feature, a bit set to '0' indicates not support
            of the profile feature. Bits are numbered left to right
            (MSB = 0). The possible values are encoded starting from
            bit a12 to a47. Bit a12 represents bit 0 of this
            enumeration, a47 is bit 35 in this attribute encoding."
    ::= {pktcDectFP 8 }

pktcDectFPExtendedCapabilities    OBJECT-TYPE
    SYNTAX      BITS {
                       unused0(0),
                       unused1(1),
                       unused2(2),
                       unused3(3),
                       unused4(4),
                       unused5(5),
                       unused6(6),
                       unused7(7),
                       unused8(8),
                       unused9(9),
                       unused10(10),
                       unused11(11),
                       unused12(12),
                       unused13(13),
                       listAccess(14),
                       unused15(15),
                       unused16(16),
                       unused17(17),
                       unused18(18),
                       parallelCall(19),
                       unused20(20),
                       unused21(21),
                       unused22(22),
                       zeroEmission(23),
                       unused24(24),
                       unused25(25),
                       multipleLines(26),
                       multipleCalls(27),
                       unused28(28),
                       unused29(29),
                       unused30(30),
                       unused31(31)
                     }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the FP capabilities.
            A bit set to '1' indicates support of the specific profile
            feature, a bit set to '0' indicates not support of the
            profile feature. Bits are numbered left to right (MSB = 0).
            The possible values are encoded starting from bit a12 to
            a47.
            Bit a12 represents bit 0 of this enumeration, a47 is bit 35
            in this attribute encoding (only the most relevant are
            shown):

            'parallelCall': Common parallel call procedure support
            'listAccess':   list Access Service support
            'zeroEmission': support for Zero Emission
            'multipleLines': multiple lines support
            'multipleCalls': multiple calls support."
    ::= {pktcDectFP 9 }

pktcDectHDVoiceProfile OBJECT IDENTIFIER ::= { pktcDectObjects 2 }

pktcDectHDVoiceProfileBasicService OBJECT-TYPE
    SYNTAX      PktcSpecVersion
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the supported HD Voice
            profile for basic service."
    REFERENCE
            "PacketCable DECT-HDV Specification."
    ::= { pktcDectHDVoiceProfile 1 }

pktcDectHDVoiceProfileNCS    OBJECT-TYPE
    SYNTAX      PktcSpecVersion
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the supported HD voice
            profile for NCS."
    REFERENCE
            "PacketCable DECT-HDV Specification"
    ::= { pktcDectHDVoiceProfile 2 }

pktcDectHDVoiceProfileSIP OBJECT-TYPE
    SYNTAX      PktcSpecVersion
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the supported HD Voice
            profile for SIP."
    REFERENCE
            "PacketCable DECT-HDV Specification"
    ::= { pktcDectHDVoiceProfile 3 }

pktcDectCodec OBJECT IDENTIFIER ::= { pktcDectObjects 3 }

pktcDectCodecPrefList OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "This attribute represents the codec selection in prefered
            order from left to right. The codec list is comma separated
            with no additional characters between code names.
            When a user associated with an endpoint linked to this
            FP has configured its own preferred codec list this
            attribute is ignored."
    REFERENCE
            "PacketCable DECT-HDV Specification"
    DEFVAL      { "G722,PCMU,PCMA" }
    ::= { pktcDectCodec 1 }

pktcDectDTMF OBJECT IDENTIFIER ::= { pktcDectObjects 4 }

pktcDectDTMFToneDuration OBJECT-TYPE
    SYNTAX      Unsigned32
    UNITS       "milliseconds"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "This attribute specifies the tone duration for DTMF
            defined length events sent by a PP to the FP."
    REFERENCE
            "PacketCable DECT-HDV Specification"
    DEFVAL      { 100 }
    ::= { pktcDectDTMF 1 }

pktcDectBargeIn OBJECT IDENTIFIER ::= { pktcDectObjects 5 }

pktcDectBargeInEnabled OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "This attribute indicates the barge-in state of this
            instance. The value 'true' indicates barge-in is enabled.
            The value 'false' indicates barge-in is disabled."
    REFERENCE
            "PacketCable DECT-HDV Specification"
    DEFVAL  { true }
    ::= { pktcDectBargeIn 1 }

pktcDectServiceStatus OBJECT IDENTIFIER ::= { pktcDectObjects 6 }

pktcDectServiceStatusDeactivationDisplay OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "This attribute indicates the configured text to display
            in the PP when the PacketCable Client service is
            disconnected."
    REFERENCE
            "PacketCable DECT-HDV Specification"
    DEFVAL      { "Service Deactivated" }
    ::= { pktcDectServiceStatus 1 }

pktcDectServiceStatusConnectivityDisplay OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "This attribute indicates the configured text to display
            in the PP when the PacketCable Client has no Network
            (Service) Connectivity."
    REFERENCE
            "PacketCable DECT-HDV Specification"
    DEFVAL      { "Network Unavailable" }
    ::= { pktcDectServiceStatus 2 }


pktcDectAnalogAlarmCfgTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF PktcDectAnalogAlarmCfgEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
            "This object represents the configuration of an end point
            to support the Analog Alarm Configuration."
    REFERENCE
        "PacketCable DECT-HDV Specification."
    ::= {pktcDectObjects 7 }

pktcDectAnalogAlarmCfgEntry    OBJECT-TYPE
    SYNTAX      PktcDectAnalogAlarmCfgEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The Conceptual row of pktcDectAnalogAlarmCfgTable.
        When an endpoint instance is configured to enable the analog
        Alarm Configuration, the largest POTS MDI identifier
        (PktcMdiType = 'pots'') in the endpoint takes the role of
        analog alarm port. Therefore, an endpoint is allowed to have
        only one POTS configured as an analog Alarm port.

        End points not instantiated in this object have no analog
        Alarm configured (i.e., equivalent to
        analogAlarmCfg.State = 'none')."
    INDEX {
            ifIndex
          }
    ::= {pktcDectAnalogAlarmCfgTable 1 }

PktcDectAnalogAlarmCfgEntry ::= SEQUENCE {
    pktcDectAnalogAlarmCfgState
                 INTEGER

      }

pktcDectAnalogAlarmCfgState    OBJECT-TYPE
    SYNTAX      INTEGER {
                  none(1),
                  preemptive(2),
                  simultanousCalls(3)
                }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "This attribute represents alarm configuration type
            assigned for this analog port. The possible values
            are:

            'none' indicates the end point has no analog alarm
            Configuration

            'preemptive' indicates the analog alarm is configured
            in a preemptive mode of operation.

            'SimultanousCalls' indicates the PacketCable client can
            have a regular phone call and an alarm call simultaneously.

            This type of analog alarm configuration is not applicable
            to PacketCable clients that support NCS signaling
            (i.e., E-MTAs) and a set to this attribute with this value
            is rejected."
    ::= {pktcDectAnalogAlarmCfgEntry 1 }

pktcDectPPTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF PktcDectPPEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
            "This object represents the list of PPs and related
            identifiers.
            For debugging purposes this object lists more PPs than
            the maximum number of PPs."
    ::= {pktcDectObjects 8 }

pktcDectPPEntry    OBJECT-TYPE
    SYNTAX      PktcDectPPEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The Conceptual row of pktcDectPPTable."
    INDEX {
            pktcDectPPId
          }
    ::= {pktcDectPPTable 1 }

PktcDectPPEntry ::= SEQUENCE {
    pktcDectPPId
                 Unsigned32,
    pktcDectPPIPEI
                 OCTET STRING,
    pktcDectPPTerminalID
                 Unsigned32,
    pktcDectPPStatus
                 PktcDectPPState,
    pktcDectPPRegCtrl
                 INTEGER
    }

pktcDectPPId    OBJECT-TYPE
    SYNTAX      Unsigned32 (1..128)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
            "This key represents the unique identifier of the PP.
            The Id of PPs already registered corresponds to the
            interface Index associated with the PP MDI.
            For PPs not registered the FP selects an Id outside
            the range of well known Interface Index values
            defined for the device.

            The FP lists only PPs that have previously paired or
            attempted to pair within the FP during an FP initiated
            pairing process. This avoid first time PPs from
            neighbor areas to appear on a different subscriber FP."
    ::= {pktcDectPPEntry 1 }

pktcDectPPIPEI  OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(0..5))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the International Portable
            Equipment Identifier of the device. Other than
            residential/default handset identifiers are not
            required."
    ::= {pktcDectPPEntry 2 }

pktcDectPPTerminalID    OBJECT-TYPE
    SYNTAX      Unsigned32 (1..128)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the Terminal Identifier the FP
            assigns to the PP. For simple operation the FP may maintain
            the same PP Terminal Identifier from the initial Locate
            during pairing across device initialization."
    ::= {pktcDectPPEntry 3 }

pktcDectPPStatus    OBJECT-TYPE
    SYNTAX      PktcDectPPState
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the state of a PP as seen by
            the FP based on last PP/FP interaction.

            The FP may report only the values 'idleLocked' and
            activeLocked' for registered PPs.
            Unregistered PPs are reported as 'unknown' or the latest
            failure occurred such as 'easyPINFailed',
            'easyPairingFailed'.

            Note that in no-emission mode the FP may not accurately
            report the PP state."
    ::= {pktcDectPPEntry 4 }

pktcDectPPRegCtrl    OBJECT-TYPE
    SYNTAX      INTEGER {
                         register(1),
                         deregister(2),
                         remove(3)
                        }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "This attribute provides control of the PP registration
            status.

            The value 'deregister' directs the PP to initiate the
            procedure to terminate PP access rights without deleting
            the identity of the PP in this object (e.g., for
            troubleshooting purposes).

            The value 'register' initiates the registration process
            either easy pairing or PIN registration depending on the
            FP configuration (FP.PairingType). Subsequently,
            the FP will register the PP for which the register
            action was invoked.  See the FP InitiateRegistration
            to invoke the pairing of any PP.

            The value 'remove' invokes the action to de-register the PP
            (if so) and deletes the PP information of the FP."
    ::= {pktcDectPPEntry 5 }


pktcDectPPCapabilitiesTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF PktcDectPPCapabilitiesEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This object represents the PP reported capabilities."
    ::= {pktcDectObjects 9 }

pktcDectPPCapabilitiesEntry    OBJECT-TYPE
    SYNTAX      PktcDectPPCapabilitiesEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The Conceptual row of pktcDectPPCapabilitiesTable."
    INDEX {
            pktcDectPPId
          }
    ::= {pktcDectPPCapabilitiesTable 1 }

PktcDectPPCapabilitiesEntry ::= SEQUENCE {
    pktcDectPPCapabilitiesDisplay
                 INTEGER,
    pktcDectPPCapabilitiesTone
                 INTEGER,
    pktcDectPPCapabilitiesEcho
                 INTEGER,
    pktcDectPPCapabilitiesAmbientNoiseRejection
                 INTEGER,
    pktcDectPPCapabilitiesAdaptiveVolumeCtrl
                 INTEGER,
    pktcDectPPCapabilitiesSlotType
                 BITS,
    pktcDectPPCapabilitiesStoredDisplayChars
                 Unsigned32,
    pktcDectPPCapabilitiesDisplayLines
                 Unsigned32,
    pktcDectPPCapabilitiesCharsPerDisplayLine
                 Unsigned32,
    pktcDectPPCapabilitiesScrollBehavior
                 INTEGER,
    pktcDectPPCapabilitiesProfile
                 BITS
   }

pktcDectPPCapabilitiesDisplay    OBJECT-TYPE
    SYNTAX      INTEGER {
                          na(0),
                          noDisplay(1),
                          numeric(2),
                          numericPlus(3),
                          alphanumeric(4),
                          fullDisplay(5)
                        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP display capability.
            The possible values are:
            'na' : not applicable
            'noDisplay': no display
            'numeric': numeric characters (space, 0-9, *, #)
            'numericPlus': extended numeric characters
                           (space, 0-9, *, #, a, b, c, d)
            'alphanumeric': alphanumeric characters
                            (space, 0-9, *, #, a-z and A-Z)
            'fullDisplay' : displayable characters up to 0x7F."
    ::= {pktcDectPPCapabilitiesEntry 1 }

pktcDectPPCapabilitiesTone    OBJECT-TYPE
    SYNTAX      INTEGER {
                          na(0),
                          notone(1),
                          dialTone(2),
                          e182(3),
                          dect(4)
                        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute represents the PP tone capability.
        The possible values are:
        'na': not applicable
        'notone': no tone capability supported
        'dialTone': dialtone supported
        'e182': ITU-T E.182 tones supported
        'dect': complete DECT tone set."
    ::= {pktcDectPPCapabilitiesEntry 2 }

pktcDectPPCapabilitiesEcho    OBJECT-TYPE
    SYNTAX      INTEGER {
                          na(0),
                          minTCL(1),
                          fullTCL(2),
                          voip(3)
                        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP echo capability.
            The possible values are:
            'na': not applicable
            'minTCL': &gt; 34  dB
            'fullTCL': &gt; 46 dB
            'voip' : &gt; 55 dB."
    ::= {pktcDectPPCapabilitiesEntry 3 }

pktcDectPPCapabilitiesAmbientNoiseRejection    OBJECT-TYPE
    SYNTAX      INTEGER {
                          na(0),
                          noSupport(1),
                          support(2)
                        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP ambient noise rejection
            capability. The possible values are:
            'na': not applicable
            'noSupport': no noise rejection
            'support': noise  rejection provided."
    ::= {pktcDectPPCapabilitiesEntry 4 }

pktcDectPPCapabilitiesAdaptiveVolumeCtrl    OBJECT-TYPE
    SYNTAX      INTEGER {
                          na(0),
                          noSupported(1),
                          used(2),
                          disabled(3)
                        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP adaptive volume
            control capability. The possible values are:
            'na': not applicable
            'noSupported': no adaptive volume control
            'used': supported and in use
            'disabled': supported not in use."
    ::= {pktcDectPPCapabilitiesEntry 5 }

pktcDectPPCapabilitiesSlotType    OBJECT-TYPE
    SYNTAX      BITS {
                       unused0(0),
                       unused1(1),
                       unused2(2),
                       doubleSlot(3),
                       fullSlot(4),
                       unused5(5),
                       unused6(6),
                       halfSlot(7)
                     }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP slot type
            capabilities.
            A bit set to '1' indicates support of the
            slot type,
            A bit set to '0' indicates no support of
            the slot type. Bits are numbered left to
            right (MSB = 0). The possible values are:
            'halfSlot': half slot, j = 0
            'fullSlot': full slot
            'doubleSlot': double slot"
    ::= {pktcDectPPCapabilitiesEntry 6 }

pktcDectPPCapabilitiesStoredDisplayChars    OBJECT-TYPE
    SYNTAX      Unsigned32 (0..16363)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP number of stored
            display characters."
    ::= {pktcDectPPCapabilitiesEntry 7 }

pktcDectPPCapabilitiesDisplayLines    OBJECT-TYPE
    SYNTAX      Unsigned32 (0..128)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the number of lines in the
             PP display."
    ::= {pktcDectPPCapabilitiesEntry 8 }

pktcDectPPCapabilitiesCharsPerDisplayLine    OBJECT-TYPE
    SYNTAX      Unsigned32 (0..128)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP number of characters
            per line in the display."
    ::= {pktcDectPPCapabilitiesEntry 9 }

pktcDectPPCapabilitiesScrollBehavior    OBJECT-TYPE
    SYNTAX      INTEGER {
                          na(0),
                          type1(1),
                          type(2)
                        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP scroll behavior
            capability. The possible values are:
            'na': not applicable, specified
            'type1': type 1
            'type2': type 2."
    ::= {pktcDectPPCapabilitiesEntry 10 }

pktcDectPPCapabilitiesProfile    OBJECT-TYPE
    SYNTAX      BITS {
                       unused0(0),
                       unused1(1),
                       unused2(2),
                       unused3(3),
                       unused4(4),
                       gapSupport(5),
                       unused6(6),
                       unused7(7),
                       unused8(8),
                       unused9(9),
                       unused10(10),
                       unused11(11),
                       unused12(12),
                       unused13(13),
                       unused14(14),
                       unused15(15),
                       unused16(16),
                       unused17(17),
                       unused18(18),
                       unused19(19),
                       unused20(20),
                       unused21(21),
                       unused22(22),
                       unused23(23),
                       unused24(24),
                       unused25(25),
                       unused26(26),
                       unused27(27),
                       unused28(28),
                       unused29(29),
                       unused30(30),
                       unused31(31),
                       unused32(32),
                       unused33(33),
                       unused34(34),
                       unused35(35),
                       unused36(36),
                       unused37(37),
                       unused38(38),
                       unused39(39),
                       unused40(40),
                       zeroEmissionSupport(41),
                       unused42(42),
                       unused43(43),
                       unused44(44),
                       unused45(45),
                       unused46(46),
                       unused47(47),
                       unused48(48),
                       unused49(49),
                       multipleLlines(50),
                       parallelCall(51),
                       callIdentification(52),
                       wideband(53),
                       part3(54),
                       unused55(55),
                       unused56(56),
                       unused57(57),
                       unused58(58),
                       unused59(59),
                       unused60(60),
                       unused61(61),
                       unused62(62),
                       unused63(63),
                       unused64(64)
                     }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the PP profile feature
            capabilities.
            A bit set to '1' indicates support of the specific
            profile feature, a bit set to '0' indicates not support
            of the profile feature. Bits are numbered left to right
            (MSB = 0).
            The possible values are (only the most relevant are shown):
            'gapSupport'': GAP profile support
            'zeroEmission': Zero Emission support
            'multipleLlines': multiple lines
            'parallelCall': Common parallel call procedures
            'callIdentification': Call Identification support
            'wideband': Wideband support
            'part3' : Extended wideband speech services support"
    ::= {pktcDectPPCapabilitiesEntry 11 }

pktcDectListAccessTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF PktcDectListAccessEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
            "This object represents the list of lists stored in the FP."
    ::= {pktcDectObjects 10 }

pktcDectListAccessEntry    OBJECT-TYPE
    SYNTAX      PktcDectListAccessEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The Conceptual row of pktcDectListAccessTable."
    INDEX {
            pktcDectListAccessIndex
          }
    ::= {pktcDectListAccessTable 1 }

PktcDectListAccessEntry ::= SEQUENCE {
    pktcDectListAccessIndex
                 Unsigned32,
    pktcDectListAccesslistID
                 Unsigned32,
    pktcDectListAccessDescr
                 SnmpAdminString
      }

pktcDectListAccessIndex    OBJECT-TYPE
    SYNTAX      Unsigned32 (1..128)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This Key represents the unique identifier of the list element."
    ::= {pktcDectListAccessEntry 1 }

pktcDectListAccesslistID    OBJECT-TYPE
    SYNTAX      Unsigned32 (1..128)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute defines the ID of the supported list."
    ::= {pktcDectListAccessEntry 2 }

pktcDectListAccessDescr    OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute represents the name of the list.
        For standard list this corresponds to the exact name as the
        list is referred to in the specification.
        Vendor specific list may include name and references to
        documentation (e.g., URNs)."
    ::= {pktcDectListAccessEntry 3 }

pktcDectInternalNamesListTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF PktcDectInternalNamesListEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This object represents the list of registered PPs"
    ::= {pktcDectObjects 11 }

pktcDectInternalNamesListEntry    OBJECT-TYPE
    SYNTAX      PktcDectInternalNamesListEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The Conceptual row of pktcDectInternalNamesListTable."
    INDEX {
            pktcDectInternalNamesListIndex
          }
    ::= {pktcDectInternalNamesListTable 1 }

PktcDectInternalNamesListEntry ::= SEQUENCE {
    pktcDectInternalNamesListIndex
                 Unsigned32,
    pktcDectInternalNamesListNumber
                 Unsigned32,
    pktcDectInternalNamesListName
                 SnmpAdminString
      }

pktcDectInternalNamesListIndex    OBJECT-TYPE
    SYNTAX      Unsigned32 (1..32767)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This Key represents the unique identifier of the list element."
    ::= {pktcDectInternalNamesListEntry 1 }

pktcDectInternalNamesListNumber    OBJECT-TYPE
    SYNTAX      Unsigned32 (1..32767)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute  indicates the terminal identity number."
    ::= {pktcDectInternalNamesListEntry 2 }

pktcDectInternalNamesListName    OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute indicates the name of the internal party."
    ::= {pktcDectInternalNamesListEntry 3 }

pktcDectLineSettingsListTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF PktcDectLineSettingsListEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This object represents Information pertaining to the list.
        Operator settings to this line are performed via the NSL object.
        Primarily association of PPs to the phone line.
        A PacketCable device allows the user to modify any line
        parameter via PP access list commands with the exception of the
        'Dialing Prefix' field."

    ::= {pktcDectObjects 12 }

pktcDectLineSettingsListEntry    OBJECT-TYPE
    SYNTAX      PktcDectLineSettingsListEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The Conceptual row of pktcDectLineSettingsListTable."
    INDEX {
            pktcDectLineSettingsListIndex
          }
    ::= {pktcDectLineSettingsListTable 1 }

PktcDectLineSettingsListEntry ::= SEQUENCE {
    pktcDectLineSettingsListIndex
                 Unsigned32,
    pktcDectLineSettingsListLineId
                 Unsigned32,
    pktcDectLineSettingsListLineName
                 SnmpAdminString,
    pktcDectLineSettingsListAttachedHandsets
                 SnmpAdminString,
    pktcDectLineSettingsListDialingPrefix
                 SnmpAdminString,
    pktcDectLineSettingsListFPMelody
                 Unsigned32,
    pktcDectLineSettingsListFPVolume
                 Unsigned32,
    pktcDectLineSettingsListBlockedNB
                 TruthValue,
    pktcDectLineSettingsListMultipleCalls
                 TruthValue,
    pktcDectLineSettingsListIntrusionCall
                 TruthValue
      }

pktcDectLineSettingsListIndex    OBJECT-TYPE
    SYNTAX      Unsigned32 (1..127)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
            "This Key represents the unique identifier of the list
             element."
    ::= {pktcDectLineSettingsListEntry 1 }

pktcDectLineSettingsListLineId    OBJECT-TYPE
    SYNTAX      Unsigned32 (1..127)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the line identifier."
    ::= {pktcDectLineSettingsListEntry 2 }

pktcDectLineSettingsListLineName    OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the name of the line."
    ::= {pktcDectLineSettingsListEntry 3 }

pktcDectLineSettingsListAttachedHandsets    OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the list of registered handsets
             which are attached to the line.
             This attribute is formatted as a string where each octet
             represents the 'Terminal Identifier' of the handset.
             Note that the over the air 'Line settings list' defines
             the 'Attached handsets' as a sequence of bits, each
             representing a 'Terminal Id' handset."
    ::= {pktcDectLineSettingsListEntry 4 }

pktcDectLineSettingsListDialingPrefix    OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents a prefix to add to called
            party numbers for calls placed on the line."
    ::= {pktcDectLineSettingsListEntry 5 }

pktcDectLineSettingsListFPMelody    OBJECT-TYPE
    SYNTAX      Unsigned32 (0..128)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the melody of the FP linked to
             this line."
    ::= {pktcDectLineSettingsListEntry 6 }

pktcDectLineSettingsListFPVolume    OBJECT-TYPE
    SYNTAX      Unsigned32 (0..128)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the melody volume of the FP
             linked to this line."
    ::= {pktcDectLineSettingsListEntry 7 }

pktcDectLineSettingsListBlockedNB    OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents forbidden called party numbers
             on the line."
    ::= {pktcDectLineSettingsListEntry 8 }

pktcDectLineSettingsListMultipleCalls    OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the current mode of the line:
            The value 'true' indicates support for multiple call mode
            The value 'false' indicates support for single call mode.
            For PacketCable Client devices supporting only single call
             mode this value always use the value  'false'."
    ::= {pktcDectLineSettingsListEntry 9 }

pktcDectLineSettingsListIntrusionCall    OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the call intrusion mode for
            the line.
            The value 'true' indicates the line has 'call intrusion'
            enabled. Otherwise the value 'false' is reported.

            The PacketCable Client device should always use the
            configured BargedIn.Enabled attribute value as the highest
            possible value. It means if BargeIn.Enabled is set to 'false',
            the user can't modify the call intrusion to 'true' via list
            access commands. In the contrary, if BargeIn.Enabled is set to
            'true' the user could set this attribute to 'false' via 'line
            settings list' commands."
    ::= {pktcDectLineSettingsListEntry 10 }

pktcDectPerformanceTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF PktcDectPerformanceEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This object represents the performance statistics of each PP.
        When Zero Emission is enabled this object store statistics on
        a per call basis.
        When Zero Emission is disabled, this object may contains a
        single instance per PP (Terminal ID)
        referent to all the messages activity in the upstream direction
        (PP to FP) or maintain per call statistics."
    ::= {pktcDectObjects 13 }

pktcDectPerformanceEntry    OBJECT-TYPE
    SYNTAX      PktcDectPerformanceEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The Conceptual row of pktcDectPerformanceTable."
    INDEX {
            ifIndex
          }
    ::= {pktcDectPerformanceTable 1 }

PktcDectPerformanceEntry ::= SEQUENCE {
    pktcDectPerformanceRecordNum
                 Unsigned32,
    pktcDectPerformanceHandovers
                 Counter32,
    pktcDectPerformanceRTDelay
                 Unsigned32,
    pktcDectPerformanceSyncFailures
                 Counter32,
    pktcDectPerformanceControlFieldErrs
                 Counter32,
    pktcDectPerformancePayloadErrs
                 Counter32,
    pktcDectPerformanceSlidingCollisions
                 Counter32,
    pktcDectPerformanceLinkErrsQbit
                 Counter32
      }

pktcDectPerformanceRecordNum    OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This key represents the identifier of the logged
            statistics of a previous call. When Zero Emission is enabled
            the FP maintains an incrementing log information and
            deletes the oldest log instance when reaching the maximum
            number of entries.
            When Zero Emission is disabled this object creates a single
            instance with RecordNum = 0  and collects continuously the
            data associated with the object attributes."
    ::= {pktcDectPerformanceEntry 1 }

pktcDectPerformanceHandovers    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute indicates how many channel handovers the PP
            has realized since the first activity related to this
            logged call."
    ::= {pktcDectPerformanceEntry 2 }

pktcDectPerformanceRTDelay    OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute indicates the round trip delay calculated
            by the FP.
            The FP measures the RoundTrip Delay at the beginning of
            the call."
    ::= {pktcDectPerformanceEntry 3 }

pktcDectPerformanceSyncFailures    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute indicates the number of synchronization
            failures that have occurred during the current call."
    ::= {pktcDectPerformanceEntry 4 }

pktcDectPerformanceControlFieldErrs    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute indicates the number of Control field errors
         encountered during this time period"
    ::= {pktcDectPerformanceEntry 5 }

pktcDectPerformancePayloadErrs    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute indicates the number of CRC errors
         accumulated during this period of time."
    ::= {pktcDectPerformanceEntry 6 }

pktcDectPerformanceSlidingCollisions    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute indicates the number of sliding collisions
        detected during this period of time."
    ::= {pktcDectPerformanceEntry 7 }

pktcDectPerformanceLinkErrsQbit    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "this attribute indicates the number of link errors being
        signaled with the Q-bit during this period of time."
    ::= {pktcDectPerformanceEntry 8 }

pktcDectStatusTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF PktcDectStatusEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This object represents the PP status and related
        connectivity information"
    ::= {pktcDectObjects 14 }

pktcDectStatusEntry    OBJECT-TYPE
    SYNTAX      PktcDectStatusEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The Conceptual row of pktcDectStatusTable."
    INDEX {
            ifIndex
          }
    ::= {pktcDectStatusTable 1 }

PktcDectStatusEntry ::= SEQUENCE {
    pktcDectStatusLastLocate
                 DateAndTime,
    pktcDectStatusNumLocateMsgs
                 Counter32,
    pktcDectStatusNumConnectionFailures
                 Counter32,
    pktcDectStatusNumActivitySuccess
                 Counter32,
    pktcDectStatusLastActivityFailure
                 DateAndTime,
    pktcDectStatusRSSI
                 Unsigned32
      }

pktcDectStatusLastLocate    OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the time when the last Locate
            message was sent by the PP to the FP."
    ::= {pktcDectStatusEntry 1 }

pktcDectStatusNumLocateMsgs    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "This attribute represents the number of times the PP
            has subscribed since last FP reboot."
    ::= {pktcDectStatusEntry 2 }

pktcDectStatusNumConnectionFailures    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute represents the number of times the PP
        has failed connections with the FP since last FP
        reinitialization."
    ::= {pktcDectStatusEntry 3 }

pktcDectStatusNumActivitySuccess    OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute indicates the number of times the PP
        has initiated any activity successfully since
        last time the FP reinitializes."
    ::= {pktcDectStatusEntry 4 }

pktcDectStatusLastActivityFailure    OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute indicates the time where the last PP
        initiated activity and being rejected by the FP."
    ::= {pktcDectStatusEntry 5 }

pktcDectStatusRSSI    OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute represents the instantaneous
        Received Signal Strength from the PP."
    ::= {pktcDectStatusEntry 6 }


-- Conformance Definitions
pktcDectMibConformance OBJECT IDENTIFIER ::= { pktcDectMib 2 }
pktcDectMibCompliances OBJECT IDENTIFIER ::= { pktcDectMibConformance 1 }
pktcDectMibGroups      OBJECT IDENTIFIER ::= { pktcDectMibConformance 2 }

pktcDectCompliance MODULE-COMPLIANCE
    STATUS      current
    DESCRIPTION
            "The compliance statement for the HD Voice PacketCable
            Client device."
    MODULE -- this MODULE
    MANDATORY-GROUPS {
            pktcDectGroup
            }
    ::= { pktcDectMibCompliances 1 }

            pktcDectGroup OBJECT-GROUP
    OBJECTS {
              pktcDectFPMaxNumPP,
              pktcDectFPMaxActivePP,
              pktcDectFPLockListCfg,
              pktcDectFPZeroEmissionEnabled,
              pktcDectFPPairingType,
              pktcDectFPEasyPairingActivate,
              pktcDectFPName,
              pktcDectFPGeneralCapabilities,
              pktcDectFPExtendedCapabilities,
              pktcDectHDVoiceProfileBasicService,
              pktcDectHDVoiceProfileNCS,
              pktcDectHDVoiceProfileSIP,
              pktcDectCodecPrefList,
              pktcDectDTMFToneDuration,
              pktcDectBargeInEnabled,
              pktcDectServiceStatusDeactivationDisplay,
              pktcDectServiceStatusConnectivityDisplay,
              pktcDectAnalogAlarmCfgState,
              pktcDectListAccesslistID,
              pktcDectListAccessDescr,
              pktcDectInternalNamesListNumber,
              pktcDectInternalNamesListName,
              pktcDectLineSettingsListLineId,
              pktcDectLineSettingsListLineName,
              pktcDectLineSettingsListAttachedHandsets,
              pktcDectLineSettingsListDialingPrefix,
              pktcDectLineSettingsListFPMelody,
              pktcDectLineSettingsListFPVolume,
              pktcDectLineSettingsListBlockedNB,
              pktcDectLineSettingsListMultipleCalls,
              pktcDectLineSettingsListIntrusionCall,
              pktcDectPerformanceRecordNum,
              pktcDectPerformanceHandovers,
              pktcDectPerformanceRTDelay,
              pktcDectPerformanceSyncFailures,
              pktcDectPerformanceControlFieldErrs,
              pktcDectPerformancePayloadErrs,
              pktcDectPerformanceSlidingCollisions,
              pktcDectPerformanceLinkErrsQbit,
              pktcDectStatusLastLocate,
              pktcDectStatusNumLocateMsgs,
              pktcDectStatusNumConnectionFailures,
              pktcDectStatusNumActivitySuccess,
              pktcDectStatusLastActivityFailure,
              pktcDectStatusRSSI,
              pktcDectPPIPEI,
              pktcDectPPTerminalID,
              pktcDectPPStatus,
              pktcDectPPRegCtrl,
              pktcDectPPCapabilitiesDisplay,
              pktcDectPPCapabilitiesTone,
              pktcDectPPCapabilitiesEcho,
              pktcDectPPCapabilitiesAmbientNoiseRejection,
              pktcDectPPCapabilitiesAdaptiveVolumeCtrl,
              pktcDectPPCapabilitiesSlotType,
              pktcDectPPCapabilitiesStoredDisplayChars,
              pktcDectPPCapabilitiesDisplayLines,
              pktcDectPPCapabilitiesCharsPerDisplayLine,
              pktcDectPPCapabilitiesScrollBehavior,
              pktcDectPPCapabilitiesProfile
    }
    STATUS      current
    DESCRIPTION
            "Group of objects implemented in the HD Voice PacketCable
            Client device."
    ::= { pktcDectMibGroups 1 }
END
